Product Data Sheet
PDF Brochure
Material Safety Data
Installation Guideline
Repair Guideline
ECOSHIELD-E Sheet Membrane
IS TOUGH TO BEAT FOR PROTECTION

High Strength Polyethylene Geomembrane Protection

• High puncture resistance… has six times the puncture resistance of extruded foam board.
• Impermeable to water…additional relief from hydrostatic water pressure, resistance to contaminates.
• Durable…resistant to installation and backfill damage.
• 12’x120’ rolls minimize seams.
• Protects membrane, acts as a slip-sheet for backfill and drainage mat.

Ecoshield-E Properties
8-mil 10-mil 15-mil
Puncture Resistance ASTM D 1709 876 g. 1593 g. 1898 g.
Tensile Strength ASTM E 154 24.59 lbs. MD 34.6 lbs. MD 39.7 lbs. MD
Tear Resistance ASTM D 4533 3.48 lbs. 5.98 lbs. 8.74 lbs.
Low Temperature Impact ASTM D 1790 Resistant to -105°C Resistant to -105 C Resistant to -105 C
Water Vapor Trans. Rate ASTM E 96 .00711 g/ft/hr .00621 g./ft./hr. .00585 g./ft./hr.
Perm Rating ASTM E 96 0.0143 0.0133 0.0123
Chemical or Environmental Resistance Excellent Excellent Excellent
Methane Gas Modified ASTM D 1434 0 0 0
For a complete listing of properties, download a product brochure here (PDF)

ECOSHIELD-E Specifications

1. PRODUCT NAME

ECOSHIELD-E8
ECOSHEILD-E10
ECOSHIELD-E15

2. MANUFACTURER

EPRO SERVICES, INC.
P.O. Box 347
Derby, KS 67037
PHONE: 800-882-1896
FAX: 316-262-2529

3. PRODUCT DESCRIPTION

Basic Use: ECOSHIELD-E 8, 10 & 15 has been specifically designed to provide cost effective and high performance protection for the waterproofing membrane on vertical below-grade waterproofing applications. They also act as a slip-sheet for backfill and as a secondary independent waterproofing membrane. When used in detailing for specific water penetration points (i.e. cold joints, brick ledges, pipes), they enhance the tensile strength of the other detailing products. They are also used as a superior performing vapor and gas barriers (underslab).

Composition: ECOSHIELD-E 8, 10 & 15 are extremely tough, high strength geo-membranes made from a custom blend of polyolefin copolymers.

Benefits:
• High puncture resistance – has six times the puncture resistance of extruded foam board.
• Impermeable to water…offers additional relief from hydrostatic water pressure and resistance to earth contaminates.
• Durable…resistant to installation and backfill damage.
• Large roll sizes minimize seams.
• Protects membrane – acts as slip-sheet for backfill and drainage mat.
• Fully protects membrane at brick ledge and at footer to drain pipe.
• Easy to incorporate into detailing specific penetration points with other products.

Limitations:
• Should be stored out of weather.
• Should not be used in lieu of high-flow drainage mat if it is required .

4. TECHNICAL DATA

Properties: See chart.

Coverages: See chart.

Specification Writer: Contact EPRO Services before writing specifications on this project. Test information available upon request.

5. INSTALLATION

Preparation & Application: Should be applied in accordance with specific application guide specifications.

Tools: No special tools required for installation.

6. AVAILABILITY AND COST

Contact the local distributor and/or Authorized Applicator for availability and cost.
7. WARRANTY

Limited Warranty: EPRO warrants this product to be free from defects. EPRO makes no other warranties with respect to this product, express or implied, including without limitation the implied warranties of MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. EPRO’s liability shall be limited in all events to supplying sufficient product to retreat the specific areas to which defective product has been applied. EPRO shall have no other liability, including liability for incidental or resultant damages, whether due to breach of warranty or negligence. This warranty may not be modified or extended by representatives of EPRO or its distributors.

8. MAINTENANCE

No maintenance required.

9. TECHNICAL SERVICES AND INFORMATION

Complete technical services and information are available from EPRO
Services.